Updated November 2026

The bontrager 100 bike computer is a basic wired cycling computer designed to show the numbers most riders check on every ride: speed, distance, time and cadence, depending on the sensors you pair with it. This guide walks you through what the unit does, how to install and configure it, how to fix the most common problems, and what to weigh before you buy. By the end, you should have it mounted, calibrated to your wheel and ready to ride.

What the Bontrager 100 Bike Computer Does

Bontrager’s entry-level computers are built for riders who want clear, readable data without a touchscreen, smartphone pairing or mapping. Most units in this class use a magnetic speed sensor and show a small set of metrics on a segmented display. Owners often report that the appeal is simplicity: you press a few buttons, set your wheel size, and the numbers are there.

Shopping for one? See our guide: 6 Best Bontrager GoTime Bike Computer Options Compared (2026).

Before you start, confirm exactly what your model includes. Some packages ship with only a speed sensor, while others add a cadence sensor or a heart rate strap. Check the box or the product listing for the contents so you know which parts you need to mount. If you are still comparing models, the guide to Trip 100 Bike Computer: Setup, Settings and Troubleshooting Steps (2026) covers a similar class of unit and explains which settings tend to matter most.

Before You Install: Tools and Parts Checklist

Gather everything first so you are not stopping halfway through the install. Most setups need only basic hand tools.

  • The computer head unit and its mounting bracket
  • Speed sensor and magnet (usually attached to a spoke)
  • Cadence sensor and crank magnet, if included
  • Zip ties or the included rubber bands, depending on the design
  • A small Phillips screwdriver or Allen key, if the bracket requires it
  • A tape measure or ruler to check wheel circumference
  • Cable ties and a cloth to clean the mounting surfaces

Step-by-Step: Installing the Bontrager 100 Bike Computer

Step 1: Mount the Head Unit

Most riders place the head unit on the handlebar or stem, where it is visible without taking your eyes far from the road. Position it so you can read it at a glance, and keep it clear of brake levers and cable routing. Tighten the bracket firmly enough that it does not rotate, but avoid overtightening plastic clamps, which can crack.

Step 2: Attach the Speed Sensor

Mount the speed sensor on the fork or chainstay so it sits a few millimeters from the magnet. The sensor and magnet should be aligned so the magnet passes within the range specified in the manual, commonly a gap of a few millimeters. Attach the magnet to a spoke on the same side, positioned so it passes the sensor on every revolution. Spin the wheel by hand and confirm the sensor is triggered each time.

Step 3: Attach the Cadence Sensor (If Included)

Place the cadence sensor on the chainstay or seatstay and attach the crank magnet to a crank arm. As with speed, the magnet must pass the sensor closely on each pedal stroke. Route all wires away from the chain and moving parts, then secure them with zip ties.

Step 4: Pair and Power On

Power the unit and follow the on-screen prompts to pair any wireless sensors. If your model uses wired connections, make sure each plug is fully seated. Spin the wheel and pedal briefly to confirm the display reacts.

Configuring Settings for Accurate Data

Accurate distance depends almost entirely on the wheel size you enter. A wrong value will make every distance and speed reading wrong, so take the time to get it right.

Measure or Look Up Your Wheel Circumference

You can measure circumference directly: mark a spot on the tire, roll the bike forward exactly one full revolution on a flat surface, and measure the distance between the marks. Many manuals also list standard circumference values for common tire sizes. Enter the result in millimeters.

Tire Size (Common Example) Approximate Circumference (mm)
700 x 25c 2105
700 x 28c 2136
700 x 32c 2155
26 x 1.95 (MTB) 2068

These are approximate values. Tire pressure and tread change the real rolling circumference slightly, so measuring your actual wheel gives the most precise result.

Set Units, Time and Display Preferences

Choose miles or kilometers, set the clock if your model shows it, and select which data fields appear on each screen. Keep the primary screen focused on the two or three numbers you check most often. Owners often report that a cluttered display is harder to use while riding.

Test the Setup

Ride a short, known loop, such as a measured quarter-mile or a route with a verified distance from another app. Compare the computer’s reading to the known distance. If the difference is large, recheck your wheel circumference before anything else.

Troubleshooting Common Problems

  1. No speed reading: Check that the magnet is on the correct spoke and passes the sensor. Adjust the sensor distance and confirm the batteries are charged.
  2. Erratic or zero cadence: Confirm the crank magnet is aligned with the cadence sensor and that no metal parts are interfering with the signal.
  3. Wrong distance: Recheck the wheel circumference setting. Even a few millimeters of error adds up over long rides.
  4. Sensor not pairing: Remove the batteries, wait briefly, reinsert them and repeat the pairing procedure. Keep other nearby sensors powered off during pairing.
  5. Display washed out in sunlight: Adjust the backlight and contrast settings, and mount the unit at a slight angle to reduce glare.

Common Mistakes to Avoid

  • Leaving the default wheel size in place after changing tires.
  • Mounting the speed magnet on the wrong side of the wheel, where it may not pass the sensor.
  • Routing cadence wires near the chain, which can cause rattling and signal dropouts.
  • Skipping a test ride, then discovering a calibration error halfway through a long event.
  • Forgetting to check battery levels before a ride, especially in cold weather.

Tips for Getting More From Your Bontrager 100 Bike Computer

Keep a spare set of batteries in your saddle bag, and note the wheel size you use in your phone so you can restore it quickly after a tire change. If you ride multiple bikes, label each sensor set so you do not mix them up. For riders who want a wider feature set later, it is worth reading the comparison of Wireless vs Wired Bike Computer: Which Is Better for Your Riding? (2026) to decide whether a wired or wireless system fits your habits.

Buying Considerations: Is This the Right Computer?

The bontrager 100 bike computer suits riders who want straightforward metrics and minimal setup. If you want turn-by-turn navigation, route uploads or extensive ride analysis, a different class of device will serve you better. Riders comparing options often look at mounting style as well. The article on Stem Mounted Bike Computer vs Out-Front Mount: Which Should You Choose? explains the tradeoffs, and iPhone as Bike Computer vs Dedicated Unit: Which Should You Choose? addresses whether a phone can replace a dedicated head unit. If you are weighing brands more broadly, Wahoo Versus Garmin Bike Computer (2026): Which Is Better for Your Riding? offers a useful reference point.

A few accessories make installation and maintenance easier. Pick items that match your sensor type and mounting style.

  • Bontrager speed and cadence sensor replacement kit: Useful if a sensor is lost or damaged, and it keeps your system consistent with the original brand. View on Amazon
  • Spare CR2032 batteries: Many small computers and sensors use coin cells, so keeping a spare pack prevents mid-ride dropouts. View on Amazon
  • Zip ties and cable management kit: Keeps sensor wires away from the chain and spokes. View on Amazon
  • Digital caliper or measuring tape for wheels: Helps you measure actual wheel circumference for accurate distance. View on Amazon

FAQ

How do I find the correct wheel size for the bontrager 100 bike computer?

Measure the circumference by rolling the bike one full revolution and measuring the distance covered, or use a value from the manual that matches your tire size. Enter the result in millimeters.

Why is my distance reading higher or lower than my GPS app?

The most common cause is an incorrect wheel circumference setting. Tire pressure and width can also shift the real rolling distance slightly, so compare readings over a longer, measured route.

Does the bontrager 100 bike computer need a sensor to work?

Speed data requires a speed sensor and magnet. Cadence requires a separate sensor if your model supports it. Check your package contents to confirm what is included.

How often should I replace the batteries?

Battery life depends on usage and the specific model, so check the manual for estimates. Owners often recommend checking the batteries before long rides and carrying a spare.

Can I use the computer on more than one bike?

Yes, but you will need to move the head unit and sensors between bikes and update the wheel size each time. Labeling sensors helps prevent mix-ups.

Why does the speed sensor stop working in the rain?

Moisture or debris on the magnet or sensor can interrupt the signal. Wipe both surfaces dry and confirm the gap is still within the manufacturer’s range after a wet ride.

Is there a way to reset the computer to factory settings?

Most units include a reset option in the settings menu. Consult the manual for the exact procedure, as it varies by model. Resetting will erase your custom settings, so note your wheel size first.

Should I consult a professional for installation?

Most riders can install a basic computer at home. If you are unsure about sensor alignment, cable routing or any mechanical issue, a local bike shop can check the setup quickly and safely.

Conclusion

The bontrager 100 bike computer is a practical choice for riders who want clear, essential data without complexity. Installing the sensors carefully, entering an accurate wheel circumference and running a short test ride will get you most of the accuracy you need. Keep spare batteries and a simple checklist handy, and the unit should serve you reliably ride after ride.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our cycling apparel & tech guides, checking product details against manufacturer specifications and owner feedback.